北京大学学报(医学版) ›› 2019, Vol. 51 ›› Issue (1): 43-48. doi: 10.19723/j.issn.1671-167X.2019.01.008

• 论著 • 上一篇    下一篇

不同温度新型大气压冷等离子体处理对牙本质粘接强度的影响

朱晓鸣1,齐璇2,李德利1,张玉玮3,李和平4,谭建国2,()   

  1. 1. 北京大学口腔医学院·口腔医院,第二门诊部 国家口腔疾病临床医学研究中心 口腔数字化医疗技术和材料国家工程实验室 口腔数字医学北京市重点实验室,北京 100101
    2. 北京大学口腔医学院·口腔医院修复科,北京 100081
    3. 航天中心医院口腔科,北京 100049
    4. 清华大学工程物理系,北京 100084
  • 收稿日期:2018-10-11 出版日期:2019-02-18 发布日期:2019-02-26
  • 通讯作者: 谭建国 E-mail:kqtanjg@bjmu.edu.cn
  • 基金资助:
    国家自然科学基金(812200805)

Effect of a novel cold atmospheric plasma jet treatment with different temperatures on resin-dentin bonding

Xiao-ming ZHU1,Xuan QI2,De-li LI1,Yu-wei ZHANG3,He-ping LI4,Jian-guo TAN2,()   

  1. 1. Second Clinical Division, Peking University School and Hospital of Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Laboratory for Digital and Material Technology of Stomatology & Beijing Key Laboratory of Digital Stomatology, Beijing 100101, China
    2. Department of Prosthodontics, Peking University School and Hospital of Stomatology, Beijing 100081, China
    3. Department of Stomatology, Aerospace Center Hospital, Beijing 100049, China
    4. Department of Engineering Physics, Tsinghua University, Beijing 100084, China
  • Received:2018-10-11 Online:2019-02-18 Published:2019-02-26
  • Contact: Jian-guo TAN E-mail:kqtanjg@bjmu.edu.cn
  • Supported by:
    Supported by the National Natural Science Fondation of China(812200805)

摘要:

目的:研究不同温度条件下新型大气压冷等离子体(radio-frequency atmospheric-pressure glow discharge,RF-APGD)处理对牙本质粘接强度的影响。方法:(1)收集新鲜拔除的、无龋坏的、完整的第三磨牙52颗,采用精密低速切割机制备平行于牙合中层牙本质薄片,每颗离体牙制备1片 [(900±100) μm]。将52个中层牙本质薄片随机分为对照组和实验组,其中对照组4片,无处理;实验组48片,按新型RF-APGD等离子体不同处理温度(4 ℃、10 ℃、20 ℃、30 ℃)平均分为4组,每大组12片。每大组按照不同处理时间(10 s,20 s,30 s)平均分为3个小组,每小组4片。采用扫描电镜观察脱矿牙本质表面形貌。(2)收集20颗完整第三磨牙随机分为对照组和4个实验组,每组4颗。对照组,无处理;4 ℃、10 ℃、20 ℃和 30 ℃ 4个实验组,每组采用新型RF-APGD等离子体处理20 s。实验组及对照组采用低速水冷精密切割机垂直于牙长轴去除牙合面牙釉质,暴露中层牙本质;采用32%磷酸酸蚀剂对牙本质表面进行酸蚀;采用牙本质粘接剂和树脂进行牙本质-树脂粘接,采用万能力学机进行牙本质-树脂粘接试件即刻微拉伸强度测定,观察不同温度新型RF-APGD等离子体处理对牙本质-树脂即刻粘接性能的影响。结果:(1)扫描电镜观察脱矿牙本质表面形貌显示,30 ℃和20 ℃新型 RF-APGD 等离子体处理组,脱矿牙本质胶原纤维表面经新型RF-APGD等离子体处理10 s即会出现微结构的破坏;10 ℃新型RF-APGD等离子体处理脱矿牙本质表面 20 s,即会出现牙本质胶原纤维之间间隙变小、表面结构坍塌等现象;4 ℃新型RF-APGD等离子体处理10 s、20 s及30 s,脱矿牙本质表面胶原纤维网状结构均能维持蓬松结构。(2)牙本质-树脂即刻微拉伸强度结果显示,对照组为(47.4±0.5) MPa,4 ℃、10 ℃、20 ℃和30 ℃新型RF-APGD等离子体处理组分别为(57.8±0.7) MPa、(51.9±0.7) MPa、(29.7±1.0) MPa和(22.2±1.5) MPa,其中4 ℃新型RF-APGD等离子体处理组所获得的微拉伸强度最高,与其他各组相比,差异具有统计学意义(P<0.05), 4 ℃和10 ℃新型RF-APGD等离子体处理组和对照组相比,牙本质-树脂微拉伸粘接强度分别提高了21.9%和9.5%。结论:4 ℃新型RF-APGD等离子体对脱矿牙本质胶原纤维的处理,较更高温度的新型RF-APGD等离子体更有利于提高牙本质-树脂的即刻粘接性能。

关键词: 等离子体, 胶原纤维, 微拉伸粘接强度

Abstract:

Objective: To investigate the effect of different treatment temperatures of a novel cold atmospheric plasma jet treatment on the resin-dentin bonding. Methods:(1) Fifty-two freshly extracted, non-carious and intact third molars were collected. The occlusal one-third of the crown was removed by means of a water-cooled low-speed Isomet saw. One dentin disc [(900 ±100) μm] was prepared for each tooth. The fifty-two dentin discs were randomly divided into control group and experimental groups, of which four were in control group, and forty-eight were divided into four experimental groups according to the different treatment temperatures (4 ℃, 10 ℃, 20 ℃ and 30 ℃) of the novel radio-frequency atmospheric-pressure glow discharge (RF-APGD) plasma jet, twelve in each group. Each experimental group was divided into three subgroups according to different treatment time (10 s, 20 s and 30 s), with four in each subgroup. The occlusal one-third of the crown was removed by means of a water-cooled low-speed Isomet saw. The morphology of demineralized dentin surfaces was analyzed using field emission scanning electron microscopy. (2) Twenty unerupted, non-carious and intact third molars were randomly divided into five groups, four in each group: control group, untreated; 4 ℃, 10 ℃, 20 ℃ and 30 ℃ experimental groups, each group was treated with the RF-APGD plasma jet for 20 s. The micro-tensile resin dentin bond strength was tested after 20 s RF-APGD plasma jet treatment with different temperatures, using a universal mechanical machine. Results:(1)The field emission scanning electron micro-scopy results indicated that when compared with the control group, a 10 s RF-APGD plasma jet treatment with 30 ℃ and 20 ℃ collapsed the collagen scaffold. Collagen fibrils maintained an uncollapsed three-dimensional structure after the 4 ℃ RF-APGD plasma jet treatment for even 30 s treatment. (2) The microtensile resin dentin bond strength results of the 4 ℃ RF-APGD plasma jet treatment group (57.8±0.7) MPa were significantly higher than that of the control group [(47.4±0.5) MPa] and 10 s, 20 s and 30 s RF-APGD plasma treatment group [(51.9±0.7) MPa,(29.7±1.0) MPa and (22.2±1.5) MPa] with statistically significant difference (P<0.05). Compared with the control group, the micro-tensile bond strength increased about 21.9% and 9.5% after 4 ℃ and 10 ℃ RF-APGD plasma jet treatment, respectively. Conclusion:Compared with other treatment temperatures, this novel RF-APGD plasma jet treatment with the temperature of 4 ℃ can preserve the three-dimensional morphology of demineralized dentin better, and can improve the resin-dentin bonding.

Key words: Plasma, Dentin collagen, Micro-tensile bond strength

中图分类号: 

  • R783.4

图1

对照组及30 ℃ 新型RF-APGD等离子体处理脱矿牙本质扫描电镜结果"

图2

20 ℃ 新型RF-APGD等离子体处理脱矿牙本质扫描电镜结果"

图3

10 ℃ 新型RF-APGD等离子体处理脱矿牙本质扫描电镜结果"

图4

4 ℃ 新型RF-APGD等离子体处理脱矿牙本质扫描电镜结果。。。"

[1] Liu Y, Liu Q, Yu QS , et al. Nonthermalatmospheric plasmas in dental restoration[J]. J Dent Res, 2016,95(5):496-505.
doi: 10.1177/0022034516629425 pmid: 26848068
[2] 熊青 . 大气压低温等离子体射流的研究[D]. 湖北: 华中科技大学, 2013.
[3] Lehmann A, Rueppell André, Schindler A , et al. Modification ofenamel and dentin surfaces by non-thermal atmospheric plasma[J]. Plasma Processe Polymer, 2013,10(3):262-270.
doi: 10.1002/ppap.201200088
[4] Zhu XM, Zhou JF, Guo H , et al. Effects of a modified cold atmospheric plasma jet treatment on resin-dentin bonding[J]. Dent Mater J, 2018,37(5):798-804.
doi: 10.4012/dmj.2017-314 pmid: 29962414
[5] Eick JD, Robinson SJ, Chappell RP , et al. The dentinal surface: its influence on dentinal adhesion. Part Ⅲ[J]. Quintessence Int, 1993,24(8):571.
pmid: 1813914
[6] Pashley DH, Tay FR, Breschi L , et al. State of the art etch-and-rinse adhesives[J]. Dent Mater, 2011,27(1):1-16.
doi: 10.1016/j.dental.2010.10.016 pmid: 21112620
[7] Hwang YJ, Lyubovitsky JG . The structural analysis of three-dimensional fibrous collagen hydrogels by raman microspectroscopy[J]. Biopolymers, 2013,99(6):349-356.
doi: 10.1002/bip.22183 pmid: 23529687
[8] Steven R, Armstrong JL, Erik W , et al. Effects of polar solvents and adhesive resin on the denaturation temperatures of demine-ralised dentine matrices[J]. J Dent, 2008,36(1):8-14.
doi: 10.1016/j.jdent.2007.10.003 pmid: 2909542
[9] Chen M, Zhang Y, Dusevich V , et al. Non-thermal atmospheric plasma brush induces HEMA grafting onto dentin collagen[J]. Dent Mater, 2014,30(12):1369-1377.
doi: 10.1016/j.dental.2014.10.004 pmid: 25458523
[10] Choi JH, Lee ES, Hong KB , et al. Surface modification of natural leather using low-pressure parallel plate plasma[J]. Surf Coat Tech, 2003,171(1/2/3):257-263.
doi: 10.1016/S0257-8972(03)00282-2
[11] Zhu XM, Guo H, Zhou JF , et al. Influences of the cold atmospheric plasma jet treatment on the properties of the demineralized dentin surfaces[J]. Plasma Sci Technol, 2018,20(4):044010.
doi: 10.1088/2058-6272/aaa6be
[12] Gwinnett AJ . Quantitative contribution of resin infiltration/hybri-dization to dentin bonding[J]. Am J Dent, 1993,6(1):7-9.
[13] Pashley DH, Carvalho RM . Dentine permeability and dentine adhesion[J]. J Dent, 1997,25(5):355.
doi: 10.1016/S0300-5712(96)00057-7 pmid: 9241954
[1] 马欣蓉,朱晓鸣,李静,李德利,李和平,谭建国. 新型大气压冷等离子体射流处理对牙本质胶原纤维交联化的影响[J]. 北京大学学报(医学版), 2022, 54(1): 83-88.
[2] 李秋菊,宫玮玉,董艳梅. 生物活性玻璃预处理对牙本质粘接界面耐久性的影响[J]. 北京大学学报(医学版), 2020, 52(5): 931-937.
[3] 唐仁韬,李欣海,于江利,冯琳,高学军. 复合树脂与玻璃陶瓷微拉伸粘接强度的体外研究[J]. 北京大学学报(医学版), 2020, 52(4): 755-761.
[4] 郑苗,詹凌璐,刘志强,李和平,谭建国. 不同等离子体处理氧化锆对人牙龈成纤维细胞黏附能力的影响[J]. 北京大学学报(医学版), 2019, 51(2): 315-320.
[5] 王月,梁宇红. 次氯酸钠溶液表面处理对牙本质粘接强度的影响[J]. 北京大学学报(医学版), 2017, 49(1): 105-109.
[6] 朱曚曚, 王国敏, 孙科, 李应龙, 潘洁. 低温等离子体用于牙齿外漂白后对牙釉质粘接强度的影响[J]. 北京大学学报(医学版), 2016, 48(1): 116-120.
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed   
[1] 张三. 中文标题测试[J]. 北京大学学报(医学版), 2010, 42(1): 1 -10 .
[2] 赵磊, 王天龙 . 右心室舒张末期容量监测用于肝移植术中容量管理的临床研究[J]. 北京大学学报(医学版), 2009, 41(2): 188 -191 .
[3] 万有, , 韩济生, John E. Pintar. 孤啡肽基因敲除小鼠电针镇痛作用增强[J]. 北京大学学报(医学版), 2009, 41(3): 376 -379 .
[4] 张燕, 韩志慧, 钟延丰, 王盛兰, 李玲玲, 郑丹枫. 骨骼肌活组织检查病理诊断技术的改进及应用[J]. 北京大学学报(医学版), 2009, 41(4): 459 -462 .
[5] 赵奇, 薛世华, 刘志勇, 吴凌云. 同向施压测定自酸蚀与全酸蚀粘接系统粘接强度[J]. 北京大学学报(医学版), 2010, 42(1): 82 -84 .
[6] 林红, 王玉凤, 吴野平. 学校生活技能教育对小学三年级学生行为问题影响的对照研究[J]. 北京大学学报(医学版), 2007, 39(3): 319 -322 .
[7] 丰雷, 程嘉, 王玉凤. 注意缺陷多动障碍儿童的运动协调功能[J]. 北京大学学报(医学版), 2007, 39(3): 333 -336 .
[8] 李岳玲, 钱秋瑾, 王玉凤. 儿童注意缺陷多动障碍成人期预后及其预测因素[J]. 北京大学学报(医学版), 2007, 39(3): 337 -340 .
[9] . 书讯[J]. 北京大学学报(医学版), 2007, 39(3): 225 -328 .
[10] 牟向东, 王广发, 刁小莉, 阙呈立. 肺黏膜相关淋巴组织型边缘区B细胞淋巴瘤一例[J]. 北京大学学报(医学版), 2007, 39(4): 346 -350 .