无牙颌印模用个别托盘椅旁计算机辅助设计和三维打印系统建立与临床初步评价

doi:10.19723/j.issn.1671-167X.2019.02.028

北京大学学报（医学版） ›› 2019, Vol. 51 ›› Issue (2): 349-355. doi: 10.19723/j.issn.1671-167X.2019.02.028

无牙颌印模用个别托盘椅旁计算机辅助设计和三维打印系统建立与临床初步评价

王冠博¹,叶红强¹,陈虎²,王勇²,孙玉春^2,^∆(),周永胜^1,^∆()

^1. 北京大学口腔医学院·口腔医院,修复科国家口腔疾病临床医学研究中心口腔数字化医疗技术和材料国家工程实验室口腔数字医学北京市重点实验室, 北京 100081;
^2. 北京大学口腔医学院·口腔医院口腔医学数字化研究中心国家口腔疾病临床医学研究中心口腔数字化医疗技术和材料国家工程实验室口腔数字医学北京市重点实验室,卫生部口腔医学计算机应用工程技术研究中心,北京 100081;

收稿日期:2017-06-12 出版日期:2019-04-18 发布日期:2019-04-26
通讯作者: 孙玉春,周永胜 E-mail:polarshining@163.com;kqzhouysh@hsc.pku.edu.cn
基金资助:
首都卫生发展科研专项(2016-1-4101);科技北京百名领军人才培养工程(Z171100001117169)

Establishment and preliminary clinical evaluation of edentulous custom trays designed and fabricated by chair-side CAD and 3D printing systems

Kuan-paul WANG¹,Hong-qiang YE¹,Hu CHEN²,Yong WANG²,Yu-chun SUN^2,^∆(),Yong-sheng ZHOU^1,^∆()

^1. Department of Prosthodontics, Peking University School and Hospital of Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Laboratory for Digital and Material Technology of Stomatology & Beijing Key Laboratory of Digital Stomatology, Beijing 100081, China;
^2. Center of Digital Dentistry, Peking University School and Hospital of Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Laboratory for Digital and Material Technology of Stomatology & Beijing Key Laboratory of Digital Stomatology,Research Center of Engineering and Technology for Digital Dentistry, Ministry of Health, Beijing 100081, China;

Received:2017-06-12 Online:2019-04-18 Published:2019-04-26
Contact: Yu-chun SUN,Yong-sheng ZHOU E-mail:polarshining@163.com;kqzhouysh@hsc.pku.edu.cn
Supported by:
the Capital’s Funds for Health Improvement and Research(2016-1-4101);the Project for Culturing Leading Talents in Scientific and Technological Innovation of Beijing(Z171100001117169)

摘要/Abstract

摘要：

目的: 采用自主研发的无牙颌个别托盘椅旁数字化系统设计并三维打印无牙颌个别托盘,用视觉模拟评分法,基于医师对该个别托盘制取终印模的满意度,初步评价其临床应用效果。方法: 由三位经过统一操作流程培训的修复医师随机接诊于北京大学口腔医院就诊的15名上、下颌牙列缺失患者,分别采用自主研发无牙颌个别托盘椅旁数字化系统和传统手工法制作无牙颌个别托盘,高流动型硅橡胶印模材制取终印模。采用视觉模拟评分法设计调查问卷,由制取终印模的三位医师根据制取印模的满意程度填写调查问卷,进行满意度调查。结果: 根据制取印模的满意程度,使用自主研发无牙颌个别托盘椅旁数字化系统制作的个别托盘与传统手工法制作的无牙颌个别托盘在口腔内试戴(整体尺寸、外形、是否利于握持等)的平均满意度分别为9.18±0.19和8.23±0.22,两者差异有统计学意义(P<0.05);试戴时边缘位置(边缘伸展、系带切迹)的平均满意度分别为8.91±0.40和7.96±0.23,两者差异有统计学意义(P<0.05);托盘稳定性的平均满意度分别为8.80±0.83和8.01±0.81,两者差异有统计学意义(P<0.05);终印模制取效果(完整性、印模材厚度、是否漏出托盘、边缘形态)的平均满意度分别为8.94±0.68和7.99±0.42,两者差异有统计学意义(P<0.05);优质终印模获取难度(重复次数、效率)的平均满意度分别为9.20±0.37和7.88±0.22,两者差异有统计学意义(P<0.05);整体的平均满意度分别为 9.11±0.49和7.95±0.15,两者差异有统计学意义(P<0.05)。结论: 使用自主研发无牙颌个别托盘椅旁数字化系统制作的个别托盘制取终印模的医师满意度高于传统手工光固化法制作的个别托盘, 达到临床要求,可进一步在临床上推广使用。

关键词: 义齿, 全口, 计算机辅助设计, 打印, 三维, 个别托盘

Abstract:

Objective: To design and fabricate edentulous custom trays by chair-side computer-aided design and 3-dimensional printing (CAD/3DP) system of independent research and development and to evaluate their clinical effects based on prosthodontists’ satisfaction using the visual analogue scale (VAS).Methods: Fifteen edentulous patients were randomly recruited by three prosthodontists who passed the unified operating process training. The custom trays for each patient were fabricated using both chair-side CAD/3DP system of independent development and manually conventional method, and the final impressions were made by silicone impression materials (light body). The prosthodontist’s satisfaction was surveyed by the three prosthodontists via the questionnaire based on visual analogue scales.Results: In the degree of the prosthodontist’s satisfaction of final impressions, the average satisfactions of “try in” (the overall size, shape, convenience, etc.) on the 3DP custom tray made by independent development chair-side system and the manually conventional method were 9.18±0.19 and 8.23±0.22, respectively. The average satisfactions of the border line position (border extensions, frenal notch)were 8.91±0.40 and 7.96±0.23, respectively. The average satisfactions of the stability in border molding were 8.80±0.83 and 8.01±0.81, respectively. The average satisfactions of the quality of final impression (completeness, thickness of impression material, exposure of custom tray, shape of border) were 8.94±0.68 and 7.99±0.42, respectively. The average satisfactions of the difficulty of high quality impression (times of repetition, efficiency) were 9.20±0.37 and 7.88±0.22, respectively. The average satisfactions of the overall satisfaction were 9.11±0.49 and 7.95±0.15, respectively. There was signi-ficant difference in the satisfaction of “try in”, border line position, stability in border molding, quality of final impression, difficulty of high quality impression, and overall satisfaction between the 3DP custom tray made by chair-side system of independent development and the manually conventional method (P<0.05).Conclusion: In the degree of the prosthodontist’s satisfaction of final impression, the 3DP custom tray made by chair-side system of independent development is higher than that of the conventional custom tray, and it meets the clinical requirements and can be popularized in clinical application.

Key words: Denture, complete, Computer-aided design, Printing, three-dimensional, Custom trays

中图分类号:

R783.6

王冠博,叶红强,陈虎,王勇,孙玉春,周永胜. 无牙颌印模用个别托盘椅旁计算机辅助设计和三维打印系统建立与临床初步评价[J]. 北京大学学报（医学版）, 2019, 51(2): 349-355.

Kuan-paul WANG,Hong-qiang YE,Hu CHEN,Yong WANG,Yu-chun SUN,Yong-sheng ZHOU. Establishment and preliminary clinical evaluation of edentulous custom trays designed and fabricated by chair-side CAD and 3D printing systems[J]. Journal of Peking University(Health Sciences), 2019, 51(2): 349-355.

图/表 5

图1

图2

图3

图4

表1

两种个别托盘制取终印模的医师满意度 (x?±s)"

Items	Independent development custom tray chair-side CAD/3DP system	Conventional method	t	P value
“Try in” (the overall size, shape, convenience, etc.)	9.18±0.19	8.23±0.22	16.660	$<$ 0.01
Border line position (border extensions, frenal notch)	8.91±0.40	7.96±0.23	9.856	$<$ 0.01
Stability in border molding	8.80±0.83	8.01±0.81	5.320	$<$ 0.01
Quality of final impression (completeness, thickness of impression material, exposure of custom tray, shape of border)	8.94±0.68	7.99±0.42	6.721	$<$ 0.01
Difficulty of high quality impression (times of repetition, efficiency)	9.20±0.37	7.88±0.22	12.988	$<$ 0.01
Overall satisfaction	9.11±0.49	7.95±0.15	8.750	$<$ 0.01

表1

参考文献 21

[1]	冯海兰, 徐军 . 口腔修复学[M]. 2版. 北京: 北京大学医学出版社, 2013: 267-269.
[2]	Basker RM, Davenport JC, Thomason JM . Prosthetic treatment of the edentulous patient[M]. 4th ed. Oxford: Blackwell, 2002: 130-149.
[3]	Zarb GA, Bolender GL, Eckert SE , et al. Prosthodontic treatment for edentulous patients[M]. 13th ed. St. Louis: Elsevier Mosby, 2013: 170-179.
[4]	Boucher CO . Complete dentureprosthodontics: the state of the art[J]. J Prosthet Dent, 2004,92(4):309-315. doi: 10.1016/j.prosdent.2004.05.017
[5]	Rahn AO, Ivanhoe JR, Plummer KD. 全口义齿教科书[M]. 6版. 冯海兰,译. 北京: 人民卫生出版社, 2011: 74-79.
[6]	Petrie CS, Walker MP, Williams K . A Survey of U.S. prosthodontists and dental schools on the current materials and methods for final impressions for complete denture prosthodontics[J]. J Prosthodont, 2005,14(4):253-262. doi: 10.1111/jopr.2005.14.issue-4
[7]	Al-Ahmar AO, Lynch CD, Locke M , et al. Quality of master impressions and related materials for fabrication of complete dentures in the UK[J]. J Oral Rehabil, 2008,35(2):111-115.
[8]	van Noort R . The future of dental devices is digital[J]. Dent Mater, 2012,28(1):3-12. doi: 10.1016/j.dental.2011.10.014
[9]	Dawood A, Marti Marti B, Sauret-Jackson V , et al. 3D printing in dentistry[J]. Br Dent J, 2015,219(11):521-529. doi: 10.1038/sj.bdj.2015.914
[10]	Baroudi K, Ibraheem SN . Assessment of chair-side computer-aided design and computer-aided manufacturing restorations: a review of the literature[J]. J Int Oral Health, 2015,7(4):96-104.
[11]	Patzelt SBM, Spies BC, Kohal RJ . CAD/CAM-fabricated implant-supported restorations: a systematic review[J]. Clin Oral Implants Res, 2015,26(Suppl.11):77-85.
[12]	Williams RJ, Bibb R, Eggbeer D , et al. Use of CAD/CAM technology to fabricate a removable partial denture framework[J]. J Prosthet Dent, 2006,96(2):96-99. doi: 10.1016/j.prosdent.2006.05.029
[13]	吴琳, 吕培军, 王勇 , 等. 可摘局部义齿支架铸型的计算机辅助设计与制作[J]. 中华口腔医学杂志, 2006,41(7):432-435.
[14]	孙玉春, 吕培军, 王勇 , 等. 计算机辅助设计与快速成形技术辅助制作全口义齿的探讨[J]. 中华口腔医学杂志, 2007,42(6):324-329.
[15]	Chen H, Yang X, Chen L , et al. Application of FDM three-dimensional printing technology in the digital manufacture of custom edentulous mandible trays[J]. Sci Rep, 2016,6:19207. doi: 10.1038/srep19207
[16]	陈虎, 赵甜, 王勇 , 等. 基于初印模三维扫描的无牙颌上颌个性化托盘计算机辅助设计及三维打印[J]. 北京大学学报(医学版), 2016,48(5):900-904. doi: 10.3969/j.issn.1671-167X.2016.05.028
[17]	魏菱, 陈虎, 周永胜 , 等. 数字化全口义齿个别托盘制作与临床应用时间评价[J]. 北京大学学报(医学版), 2017,49(1):86-91.
[18]	Liu Q, Leu MC, Schmitt SM . Rapid prototyping in dentistry: technology and application[J]. Int J Adv Manuf Technol, 2006,29(3):317-335. doi: 10.1007/s00170-005-2523-2
[19]	Torabi K, Farjood E, Hamedani S . Rapid prototyping technologies and their applications in prosthodontics, a review of literature[J]. J Dent, 2015,16(1):1-9.
[20]	徐军 . 总义齿与可摘局部义齿的设计[M]. 北京: 中国大百科全书出社, 2005: 16-17.
[21]	Chang JJ, Chen JH, Lee HE , et al. Maximizing mandibular denture retention in the sublingual space[J]. Int J Prosthodont, 2011,24(5):460-464.

Metrics

Viewed

Full text

Abstract

Cited

Shared

Discussed

无牙颌印模用个别托盘椅旁计算机辅助设计和三维打印系统建立与临床初步评价

Establishment and preliminary clinical evaluation of edentulous custom trays designed and fabricated by chair-side CAD and 3D printing systems

RICH HTML

PDF (PC)

摘要/Abstract

引用本文

使用本文

图/表 5

参考文献 21

相关文章 15

Metrics

本文评价

推荐阅读 10

[1]	刘思民,赵一姣,王晓燕,王祖华. 动态导航下不同深度环钻定位精确度的体外评价[J]. 北京大学学报（医学版）, 2022, 54(1): 146-152.
[2]	李怡,王丽瑜,刘晓强,周倜,吕季喆,谭建国. 不同材料及厚度椅旁CAD/CAM瓷贴面的边缘特征[J]. 北京大学学报（医学版）, 2022, 54(1): 140-145.
[3]	邱淑婷,朱玉佳,王时敏,王飞龙,叶红强,赵一姣,刘云松,王勇,周永胜. 姿势微笑位口唇对称参考平面的数字化构建及初步应用验证[J]. 北京大学学报（医学版）, 2022, 54(1): 193-199.
[4]	孙玉春,郭雨晴,陈虎,邓珂慧,李伟伟. 口腔精准仿生修复技术的自主创新研发与转化[J]. 北京大学学报（医学版）, 2022, 54(1): 7-12.
[5]	杨刚,胡文杰,曹洁,柳登高. 牙周健康的上颌前牙唇侧嵴顶上牙龈的三维形态分析[J]. 北京大学学报（医学版）, 2021, 53(5): 990-994.
[6]	邵振兴,宋庆法,赵宇晴,崔国庆. 一种结合线袢固定的关节镜下“嵌入式”喙突移位术:手术技术及术后影像学分析[J]. 北京大学学报（医学版）, 2021, 53(5): 896-901.
[7]	李新飞, 彭意吉, 余霄腾, 熊盛炜, 程嗣达, 丁光璞, 杨昆霖, 唐琦, 米悦, 吴静云, 张鹏, 谢家馨, 郝瀚, 王鹤, 邱建星, 杨建, 李学松, 周利群. 肾部分切除术前CT三维可视化评估标准的初步探究[J]. 北京大学学报（医学版）, 2021, 53(3): 613-622.
[8]	陈迪,徐翔宇,汪明睿,李芮,臧根奥,张悦,钱浩楠,闫光荣,范田园. 熔融沉积成型3D打印盐酸维拉帕米胃漂浮制剂的制备与体外评价[J]. 北京大学学报（医学版）, 2021, 53(2): 348-354.
[9]	尹祯敏,王子轩,陈俊锴,孙玉春,刘云松,叶红强,周永胜. 可摘局部义齿适合性方法的评价[J]. 北京大学学报（医学版）, 2021, 53(2): 406-412.
[10]	黄新瑞,李莎,高嵩. 冷冻电镜成像中噪声的滤波方法进展[J]. 北京大学学报（医学版）, 2021, 53(2): 425-433.
[11]	穆海丽,田福聪,王晓燕,高学军. 玻璃体和通用型复合树脂耐磨性的临床对照研究[J]. 北京大学学报（医学版）, 2021, 53(1): 120-125.
[12]	岳兆国,张海东,杨静文,侯建霞. 数字化评估CAD/CAM个性化基台与成品基台影响粘接剂残留的体外研究[J]. 北京大学学报（医学版）, 2021, 53(1): 69-75.
[13]	徐啸翔,曹烨,赵一姣,贾璐,谢秋菲. 数字化个齿托盘制取下颌全牙列全冠预备体印模的体外评价[J]. 北京大学学报（医学版）, 2021, 53(1): 54-61.
[14]	国丹妮,潘韶霞,衡墨笛,屈健,魏秀霞,周永胜. 应用于无牙颌种植修复设计的三维面部扫描配准方法的对比[J]. 北京大学学报（医学版）, 2021, 53(1): 83-87.
[15]	李思雨,段雪飞,曹烨. 应用超声器械改善预备体肩台的效果[J]. 北京大学学报（医学版）, 2021, 53(1): 88-94.